Skočiť na hlavný obsah

i550 protec

The award-winning i550 protec frequency inverter uses the same tried-and-tested technology used in our control cabinet inverters. It only differs in terms of a higher degree of housing protection and an adapted design. If there is not enough space in the control cabinet or the inverter has to be mounted close to the motor in various machine modules, then this versatile and reliable device is the right solution. Thanks to the extension box, a disconnect switch and operating elements can be used.
The requirements of the Ecodesign Directive, Standard EN IEC 61800-9-2, are met.
Application areas: Conveyor drives, traveling drives, winding drives, hoist drives, extruders, packaging machines, pumps, fans, ...

Highlights

  • Decentralized drive with IO-Link interface V1.1
  • Integrated diagnostic interface (micro USB) for service purposes
  • Versions with or without repair switch, with keypad or WLAN module for easy commissioning
  • Optionally available with "Safe Torque Off (STO)" with SIL 3 (EN IEC 61508) and Performance Level e (EN ISO 13849-1)
Documentation
Error codes
Fault ID: 12816
Hex: 0x3210
Description: Fault - DC bus overvoltage
Keypad display: DC Bus OV
Cause Remedy Severity/response

DC-bus voltage has exceeded the error threshold for overvoltage due to a too high braking energy or a too high mains voltage. The error threshold (display in 0x2540:006 (P208.06) results from the setting of the rated mains voltage in 0x2540:001 (P208.01).

Reduce dynamic performance of the load profile.

Check mains voltage.

Check settings for brake energy
management.

0x2541:001 (P706.01) = [0]: Connect brake resistor to the power unit and activate the integrated brake chopper

Fault
Fault ID: 12672
Hex: 0x3180
Description: UPS operation active
Keypad display: UPS oper. active
Cause Remedy Severity/response

Operation on uninterrupted 1x230V current supply (UPS) has been activated: Only a reduced output current is provided.

Switch back to operation with regular mains voltage

Warning
Fault ID: 12576
Hex: 0x3120
Description: Mains phase fault 
Keypad display: Mains Phase fail
Cause Remedy Severity/response

Mains phase failure
  • Check wiring of the mains connection.
  • Check fuses.

Fault
Fault ID: 1030
Hex: 1030
Description: Undervoltage in the DC bus
Keypad display: LU
Cause Remedy Severity/response

DC bus voltage is lower than specified in C0173.
  • Check mains voltage
  • Check supply cable

cawc
Fault ID: 1020
Hex: 1020
Description: Overvoltage in DC bus
Keypad display: OU
Cause Remedy Severity/response

Braking energy is too high. (DC−bus voltage is higher than set in C0173.)
  • Use braking unit or regenerative module.
  • Check dimensioning of the brake resistance.
Fault ID: 0016
Hex: 0016
Description: I2xt overload
Keypad display: OC6
Cause Remedy Severity/response
  • Frequent and too long acceleration processes with motor overcurrent.
  • Permanent motor overload with Imotor >Irmotor

Check drive dimensioning.
Fault ID: x018
Hex: x018
Description: I2xt overload advance warning
Keypad display: OC8
Cause Remedy Severity/response
  • Frequent and too long acceleration processes with motor overcurrent.
  • Permanent motor overload with Imotor >Irmotor

Check drive dimensioning.
Fault ID: 0015
Hex: 0015
Description: I x t overload
Keypad display: OC5
Cause Remedy Severity/response
  • Frequent and too long acceleration with overcurrent
  • Continuous overload with Imotor > 1.05 x Irx

Check drive dimensioning.
Fault ID: 0012
Hex: 0012
Description: Motor cable earth fault
Keypad display: OC2
Cause Remedy Severity/response

One of the motor phases has
earth contact.
  • Search for cause of short circuit.
  • Check motor cable.
Fault ID: 0011
Hex: 0011
Description: Short circuit of motor cable
Keypad display: OC1
Cause Remedy Severity/response

Short circuit

Excessive capacitive charging
current in the motor cable.
  • Search for cause of short circuit.

  • Check motor cable.

    Use motor cable which is shorter
    or of lower capacitance.
Fault ID: 9090
Hex: 0x2382
Description: Fault - Device utilization (ixt) too high
Keypad display: Ixt error
Cause Remedy Severity/response

Device utilisation (ixt) too high by frequent and too long acceleration processes.

Check drive sizing. 

  • Reduce the maximum current of the inverter 0x6073 (P324.00). 
  • In case of high mass inertias, reduce maximum current of the inverter 0x6073 (P324.00) to 150 %.

Fault (configurable)

  • The event can only be reset after a blocking time.

Blocking time: 2 s

Setting parameters: 0x2D40:005 (P135.05)
Fault ID: 9040
Hex: 0x2350
Description: CiA: i²xt overload (thermal state)
Keypad display: i2t motor
Cause Remedy Severity/response

Motor thermally overloaded, e. g. by an impermissible continuous current or by frequent or too long acceleration processes.

Check drive sizing.

  • Check machine/driven mechanics for excessive load.
  • Check settings of the motor data.
  • Reduce values for slip compensation 0x2B09:001 (P315.01), 0x2B09:002 (P315.02) and oscillation damping 0x2B0A:001 (P318.01), 0x2B0A:002 (P318.02).

Fault (configurable)

  • The event can only be reset after a blocking time.

Blocking time: 2 s

Setting parameters: 0x2D4B:003 (P308.03)
Fault ID: 9024
Hex: 0x2340
Description: Short circuit at the motor end
Keypad display: Motor shorted
Cause Remedy Severity/response

Short circuit of motor cable

Check motor cable for short circuit.

Fault

  • The inverter is disabled immediately. The motor has no torque (is coasting).
  • The event can only be reset after a blocking time.

Blocking time: 2 s
Fault ID: 8992
Hex: 0x2320
Description: Short circuit or earth leakage at the motor end
Keypad display: Earth leak
Cause Remedy Severity/response
  • Short circuit/earth fault of motor cable
  • Capacitive charging current of the motor cable too high.
  • Check motor cable.
  • Check length of the motor cable.
  • Use shorter or lower-capacitance motor cable.

Fault

  • The inverter is disabled immediately. The motor has no torque (is coasting).
  • The event can only be reset after a blocking time.

Blocking time: 2 s
Fault ID: 8784
Hex: 0x2250
Description: CiA: Continuous over current (internal)
Keypad display: PU over current
Cause Remedy Severity/response
  • Continuous overcurrent on the inverter/ motor side.
  • Overcurrent at the brake chopper (brake transistor).
  • DC bus relay has not been closed due to a malfunction.
  • Check motor and wiring for short circuits.
  • Check brake resistor and wiring.
  • Check motor switching.
  • Check settings of the motor data.

Fault

  • The inverter is disabled immediately. The motor has no torque (is coasting).
  • The event can only be reset after a blocking time.

Blocking time: 2 s
Prihlásiť sa na odber i550 protec