Skip to main content

8400 TopLine

The 8400 TopLine frequency inverter with servo qualities is suitable for dynamic movements.

The requirements of the Ecodesign Directive, standard EN IEC 61800-9-2, are met.

Highlights

  • Servo control with feedback also for synchronous motors
  • Axis bus for electrical shaft
  • Optionally available with "Safe Torque Off (STO)"
Documentation
Title Language Document type Version File
"Actuator Torque" technology application DE Commissioning 1.1
"Actuator Torque" technology application EN Commissioning 1.1
"Position Follower" technology application DE Commissioning 1.0
"Position Follower" technology application EN Commissioning 1.0
"Position Sequencer" technology application DE Commissioning 1.0
"Position Sequencer" technology application EN Commissioning 1.0
"Electrical Shaft Master Slave" technology application DE Commissioning 1.0
"Electrical Shaft Master Slave" technology application EN Commissioning 1.0
"Winder Tension" technology application DE Commissioning 1.0
"Winder Tension" technology application EN Commissioning 1.0
"Winder Dancer" technology application DE Commissioning 1.0
"Winder Dancer" technology application EN Commissioning 1.0
PLC Designer V3 Application Samples DE Commissioning 2.1
PLC Designer V3 Application Samples EN Commissioning 2.1
CANopen 8400 DE Operating instructions 4.2
CANopen 8400 EN Operating instructions 4.2
EtherCAT® 8400 E84AYCET DE Operating instructions 3.1
EtherCAT® 8400 E84AYCET EN Operating instructions 3.1
EtherNet/IP™ 8400 E84AYCEO DE Operating instructions 3.0
EtherNet/IP™ 8400 E84AYCEO EN Operating instructions 3.0
POWERLINK 8400 E84AYCEC DE Operating instructions 3.0
POWERLINK 8400 E84AYCEC EN Operating instructions 3.0
PROFIBUS 8400 E84AYCPM DE Operating instructions 2.2
PROFIBUS 8400 E84AYCPM EN Operating instructions 2.2
PROFINET 8400 E84AYCER DE Operating instructions 11.0
PROFINET 8400 E84AYCER EN Operating instructions 11.0
Commissioning 8400 TopLine DE Commissioning 11.1
Commissioning 8400 TopLine EN Commissioning 11.1
Project planning 8400 TopLine DE Project planning 11.3
Project planning 8400 TopLine EN Project planning 11.3
Flyer 8400 TopLine frequency inverter ZH Flyer 2.0
Flyer 8400 TopLine frequency inverter PT Flyer 2.0
Flyer 8400 TopLine frequency inverter PL Flyer 2.0
Flyer 8400 TopLine frequency inverter IT Flyer 2.0
Flyer 8400 TopLine frequency inverter HU Flyer 2.0
Flyer 8400 TopLine frequency inverter FR Flyer 2.0
Flyer 8400 TopLine frequency inverter CS Flyer 2.0
Flyer 8400 TopLine frequency inverter DE Flyer 2.0
Flyer 8400 TopLine frequency inverter EN Flyer 2.0
Error codes
Fault ID: 12816
Hex: 0x3210
Description: Fault - DC bus overvoltage
Keypad display: DC Bus OV
Cause Remedy Severity/response

DC-bus voltage has exceeded the error threshold for overvoltage due to a too high braking energy or a too high mains voltage. The error threshold (display in 0x2540:006 (P208.06) results from the setting of the rated mains voltage in 0x2540:001 (P208.01).

Reduce dynamic performance of the load profile.

Check mains voltage.

Check settings for brake energy
management.

0x2541:001 (P706.01) = [0]: Connect brake resistor to the power unit and activate the integrated brake chopper

Fault
Fault ID: 12672
Hex: 0x3180
Description: UPS operation active
Keypad display: UPS oper. active
Cause Remedy Severity/response

Operation on uninterrupted 1x230V current supply (UPS) has been activated: Only a reduced output current is provided.

Switch back to operation with regular mains voltage

Warning
Fault ID: 12576
Hex: 0x3120
Description: Mains phase fault 
Keypad display: Mains Phase fail
Cause Remedy Severity/response

Mains phase failure
  • Check wiring of the mains connection.
  • Check fuses.

Fault
Fault ID: 1030
Hex: 1030
Description: Undervoltage in the DC bus
Keypad display: LU
Cause Remedy Severity/response

DC bus voltage is lower than specified in C0173.
  • Check mains voltage
  • Check supply cable

cawc
Fault ID: 1020
Hex: 1020
Description: Overvoltage in DC bus
Keypad display: OU
Cause Remedy Severity/response

Braking energy is too high. (DC−bus voltage is higher than set in C0173.)
  • Use braking unit or regenerative module.
  • Check dimensioning of the brake resistance.
Fault ID: 0016
Hex: 0016
Description: I2xt overload
Keypad display: OC6
Cause Remedy Severity/response
  • Frequent and too long acceleration processes with motor overcurrent.
  • Permanent motor overload with Imotor >Irmotor

Check drive dimensioning.
Fault ID: x018
Hex: x018
Description: I2xt overload advance warning
Keypad display: OC8
Cause Remedy Severity/response
  • Frequent and too long acceleration processes with motor overcurrent.
  • Permanent motor overload with Imotor >Irmotor

Check drive dimensioning.
Fault ID: 0015
Hex: 0015
Description: I x t overload
Keypad display: OC5
Cause Remedy Severity/response
  • Frequent and too long acceleration with overcurrent
  • Continuous overload with Imotor > 1.05 x Irx

Check drive dimensioning.
Fault ID: 0012
Hex: 0012
Description: Motor cable earth fault
Keypad display: OC2
Cause Remedy Severity/response

One of the motor phases has
earth contact.
  • Search for cause of short circuit.
  • Check motor cable.
Fault ID: 0011
Hex: 0011
Description: Short circuit of motor cable
Keypad display: OC1
Cause Remedy Severity/response

Short circuit

Excessive capacitive charging
current in the motor cable.
  • Search for cause of short circuit.

  • Check motor cable.

    Use motor cable which is shorter
    or of lower capacitance.
Fault ID: 9090
Hex: 0x2382
Description: Fault - Device utilization (ixt) too high
Keypad display: Ixt error
Cause Remedy Severity/response

Device utilisation (ixt) too high by frequent and too long acceleration processes.

Check drive sizing. 

  • Reduce the maximum current of the inverter 0x6073 (P324.00). 
  • In case of high mass inertias, reduce maximum current of the inverter 0x6073 (P324.00) to 150 %.

Fault (configurable)

  • The event can only be reset after a blocking time.

Blocking time: 2 s

Setting parameters: 0x2D40:005 (P135.05)
Fault ID: 9040
Hex: 0x2350
Description: CiA: i²xt overload (thermal state)
Keypad display: i2t motor
Cause Remedy Severity/response

Motor thermally overloaded, e. g. by an impermissible continuous current or by frequent or too long acceleration processes.

Check drive sizing.

  • Check machine/driven mechanics for excessive load.
  • Check settings of the motor data.
  • Reduce values for slip compensation 0x2B09:001 (P315.01), 0x2B09:002 (P315.02) and oscillation damping 0x2B0A:001 (P318.01), 0x2B0A:002 (P318.02).

Fault (configurable)

  • The event can only be reset after a blocking time.

Blocking time: 2 s

Setting parameters: 0x2D4B:003 (P308.03)
Fault ID: 9024
Hex: 0x2340
Description: Short circuit at the motor end
Keypad display: Motor shorted
Cause Remedy Severity/response

Short circuit of motor cable

Check motor cable for short circuit.

Fault

  • The inverter is disabled immediately. The motor has no torque (is coasting).
  • The event can only be reset after a blocking time.

Blocking time: 2 s
Fault ID: 8992
Hex: 0x2320
Description: Short circuit or earth leakage at the motor end
Keypad display: Earth leak
Cause Remedy Severity/response
  • Short circuit/earth fault of motor cable
  • Capacitive charging current of the motor cable too high.
  • Check motor cable.
  • Check length of the motor cable.
  • Use shorter or lower-capacitance motor cable.

Fault

  • The inverter is disabled immediately. The motor has no torque (is coasting).
  • The event can only be reset after a blocking time.

Blocking time: 2 s
Fault ID: 8784
Hex: 0x2250
Description: CiA: Continuous over current (internal)
Keypad display: PU over current
Cause Remedy Severity/response
  • Continuous overcurrent on the inverter/ motor side.
  • Overcurrent at the brake chopper (brake transistor).
  • DC bus relay has not been closed due to a malfunction.
  • Check motor and wiring for short circuits.
  • Check brake resistor and wiring.
  • Check motor switching.
  • Check settings of the motor data.

Fault

  • The inverter is disabled immediately. The motor has no torque (is coasting).
  • The event can only be reset after a blocking time.

Blocking time: 2 s
Subscribe to 8400 TopLine